Swim'n Play 4ft Manuel d'utilisateur

OVALPOOL ASSEMBLY INSTRUCTIONSPart# 420869-14313 REGINA AVENUE, RAHWAY, NEW JERSEY 07065-4891Phone: (732) 574-1500 • Fax: (732) 574-1551 • www.swimnpl

Remove wall from carton. NOTE: the UP arrow onwall.Determine starting pointas the filter inlet andoutlet holes are at thebeginning of the wall.Start

11CLOSING THE WALL6Insert the 1/4" - 20x3/4" trusshead screws from inside the poolthrough the preattached insideclosure bar, through inside

12ASSEMBLE BUTTRESS7BUTTRESS TOP PLATE#12 x 1/2”SHEET METALSCREWS#12 x 1/2”SHEET METALSCREWS5/16”-18 x 1/2”HEX HEAD BOLTS5/16”-18 x 3”HEX HEAD BOLT5/1

13HOLD DOWN SHEET10RECHECKING YOUR WORK9Measure from the last strap to the outer end of the pool.Measurements in both ends should be equal. Also make

14THRU-THE-WALL SKIMMER11IMPORTANT!! BEFORE CONTINUING WITH THIS STEPYOU MUST KNOW WHICH TYPE OF THROUGH THE WALL SKIMMERYOU WILL BE USING WITH YOUR

Wall guard is optional.Tape wall guard (plastic sheeting) to pool wall 12" up fromground and smooth out on ground 12" from wall. This will

CAUTIONYOUR POOL IS DESIGNED TO PROVIDE AN AMPLE SAFETY MARGINWHEN IT STANDS ON LEVEL GROUND. FOR THIS PURPOSE A SLOPE IN EXCESS OF 2 INCHES IN ANY D

17EZ HOOK LINER INSTALLATIONATTENTION: An 8 inch cove must be placed all around the inside of the pool1. Clear all sticks and sharp objects from an ar

18VERTICALS, TOP PLATES AND RAILS15PRE-ASSEMBLY OF TOP PLATES*14No. 12 x 1/2”Sheet MetalScrewIf fencing or decking is to be installed, refer to the de

19No. 12 x 1/2”Sheet MetalScrewInsert two rails into a plate, in the same manner and using the same spacing as you have done on the bottom rail and pl

2CONTRACT INSTALLATIONSThe manufacturer is in no way affiliated with any professional pool installer. Therefore the manufacturer can assume norespons

Your pool is equipped with (3) three special warning ledges. The (1) one ledge witha large warning on top is to be installed by the entry point into

21INSTALLING TOP COVERS17FOLLOW THE INSTRUCTIONS BELOW FOR THE COVERS FOR YOUR PARTICULAR POOL4", 6" & 7" DELUXE TOP COVERSThese co

226" & 7" TWO-PIECE FULL CONTOURED COVERSlide inside cover (the cover which will be closest to the inside of the pool) into position and

237" AND 9” TWO-PIECE WRAP AROUND COVER AND PEDESTALSlide the inside cover (the cover which will be closest to the inside of the pool) into posit

24WRAP AROUND PEDESTAL1 - Insert the logo into the pedestal.2 - Place the pedestal onto the bottom of the vertical and align the holes on the side of

25WARNINGFour (4) danger labels have been provided for your safety. Apply these labels to the pool where they are easily visible to all persons using

26SAFETY TIPS - RULES AND REGULATIONSThis section is designed to acquaint you with some guidelines as to the safe operation and use of your pool.• Do

27WARNINGCheck all the metal on the pool frame and pool wall for signs of corrosion or deterioration. Remove any corrosion and touch up with paint.

A reliable pool water test kit will help to determine the daily chlorine dosage and the acid-alkaline condition of thewater. You will find in the tes

3SOME FRIENDSTO HELP OUTHammerKnifeTapeRake4” NailPliersCloth TapeCenter Stake2 x 4Sifted Earth or Pre Washed SandBroomPatio BlocksCarpentersLevelShov

4INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembl

5INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembl

6INSTALLATION • ASSEMBLY STEPSREAD CAREFULLY BEFORE STARTING POOL ASSEMBLYCONSTRUCTION CLOSE-UPSUse the illustrations below as a guide for the assembl

DDDD7Your pool must be installed on a solid level surface. After the pool location is selected drive the twoend stakes "A" into the ground

Using the “CLEARANCE SIZE” chart on page 6, determine the clearance size for your pool.With the use of the leveling device shown and a shovel start le

9ASSEMBLING THE BOTTOM STRAPS3Unpack and assemble the bottom straps with the buttress bottom plates and brackets as shownusing all necessary hardware